[magny image=”https://www.rebellegion.com/wp-content/uploads/2015/02/lobot_detail.png” title=”” description=”” align=”right” click=”1″ scroll_zoom=”1″ small_image=”https://www.rebellegion.com/wp-content/uploads/2015/02/lobot_detail-200×200.png” canvas_mode=”1″ maxwidth=”300px” zoom=”3″ dia=”250px” skin=”new-im-frame-simple,new-title-below,new-description-off,new-slider-below,new-im-magnifier-light new-im-magnifier-square” ]
Lobot was a Human male who served as the chief administrative aide to Baron Administrator Lando Calrissian on Cloud City over the planet Bespin. His brain was connected to the city’s central computer which allowed him to communicate directly with the city’s computer network. In this capacity, he served as the city’s first and only computer-liaison officer.
a. Cream colored undershirt with wide billowy sleeves and cuff at the wrist and stand-up square collar.
a. Gray in color (to match references)
b. Has a Y-shaped bib section and two pocket flaps. Top stitching is visible near side boarder of bib and side and bottom of pocket flaps.
c. Back of vest has parallel pleats at side that goes up and over the shoulder and ends at the pocket flaps near the arm pit. (Similar to shoulder tucks on the Jedi outer tunic, but extends all the way down the back of the vest.)
d. Vest may be attached to the pants in a jumpsuit fashion if desired
a. Full-length pants in the same color of the vest
b. No pockets.
a. The belt is black in color, featuring 2 layer construction. The bottom layer should be of a thin leather like material that wraps around the costumer. The top layer should be thicker and covered in a leather or leather like material.
b. The belt has a wide portion that wraps from the costumer’s right hip to left hip. The back of the belt is narrow, about 3 inches wide.
c. The top layer of the belt contains a rectangular opening in the middle of the front portion to display the greeblies. This thick portion wraps from the costumer’s right hip to left hip.
d. Greeblies include in the opening of the belt’s top layer include:
2 large silver discs
2 large black discs with a + configuration on the surface
2 Small black rectangles with silver borders
2 sets of 2 small silver rectangles
A single silver rectangle
The bottom portion of a snap
e. Connecting the vest and pants is a single small black belt loop piece centered on the back of the vest and pants. The back of the belt should sit underneath this belt loop.
a. Accurately shaped headpiece that is gray in color.
b. There is a layer of light gray felt-like material over the top rim of the headpiece.
c. LEDs can be either functional or not.
d. The headpiece is symmetrical.
Each of the two sides of the headpiece has the following:
-Four red tinted rectangular LEDs in a recessed side panel. Side panel is painted dark blue, that appears black. Black paint is also acceptable.
-One red tinted LED in a recessed circle at side of the cheeks.
-A row of white LEDs facing backwards under a clear plastic shield, no more than nine LEDs
-Two non functioning red tinted LEDs with black o-rings at the base on the back panel.
-Four small red tinted LEDs on the front panel.
-Accurately placed reflective tape.
*Costumer must be bald. A bald cap can be used to achieve the look.
a. The boots are Chelsea style – ankle boots in a gray, closely matching the vest and pants.
b. The boots should not have any outside zippers, laces or straps. An inside zipper is acceptable.
c. Heel no higher than one inch
Standard reviewed by the Costume Standards Committee 1 Feb 2015
PLEASE NOTE: The costume standards are a guide, yet are not an all inclusive outline of required elements. The judges will be looking for quality of workmanship, accurate execution and use of materials in addition to these general standards check lists. If you have a question about fabrics, colors, and parts choices for your build please contact the LCJs for your category about parts/materials you are considering before you start your build. (LCJ listing here)