Alliance Senior Officers Version B, Rogue One

ALL, Officers, Rogue One

CHARACTER DESCRIPTION
The Senior Officers (Rogue One) belong to upper command staff of the Rebel Alliance military. They are commanders of larger military units such as the Yavin 4 Special Forces division, oversee the Alliance Starfighter Command, or are liaisons for high ranking Fleet officers and work as part of Fleet command.
(Source: Star Wars Rogue One – The Ultimate Visual Guide)

REQUIRED ITEMS

Jacket

Required Details:

  1. Safari-style jacket reaching below the hip
  2. Sand or light tan medium weight cotton or similar fabric
  3. Heavily padded standing collar with a horizontal center seam.
  4. Sleeve divided into 3 sections with 1 seam placed above the elbow, and 1 seam placed mid forearm.
  5. Back elbow section of sleeves are quilted with horizontal lines of stitching, approximately 1 cm (1/2 inch) apart.
  6. Zip closure, hidden in a placket approximately 5 cm (2 inch) wide
  7. Quilted yoke with vertical stitching approximately 1 cm (1/2 in) apart.
  8. Yoke is approximately level with underarm in front and approximately the middle to lower edge of the shoulder blades in back.
  9. Yoke bottom has a an unquilted edge approximately 1 cm (1/2 inch) wide running horizontally along the front bottom edge.
  10. Two bellows/gusseted pockets with top flaps, located on the upper chest- one on either side of the front opening.
  11. Pockets attached at approximately a 20 degree angle under the yoke beginning approximately 1 cm (1/2 inch) beneath the yoke on the outside side, and widening to approximately 3-4 cm (1-1.5 inches) beneath the yoke towards the jacket center.
  12. Pockets are rounded at the bottom with a center pleat
  13. Flap has a tapered curve, with the widest part towards the outside of the jacket.
  14. Two large bellows/gusseted cargo pockets with top flaps, located approximately even with the hips-one on either side of the front opening
  15. Flaps are set at approximately a 30 degree angle with the highest point towards the center front.
  16. Pockets have rounded bottoms and a center pleat.
  17. Cloth insignia sewn onto upper right arm of jacket:
    • Insignia is white cloth with black grid of 9 squares- no outside border
    • Squares arranged in three columns of three, left to right:
      • 3 red rectangles
      • 2 grey rectangles and 1 blue or green rectangle
      • 2 crosshairs design rectangles and 1 grey rectangle

Optional Details:

  1. Top-stitching on sleeve seams
  2. Top-stitching on collar
  3. Red, or Blue piping on top pocket flaps coordinating with the color of the metal rank bade pips/circles
  4. Yoke bottom has a piped or bound seam

Additional Images:

Pants

Required Details:

  1. Utility trousers similar in style to military BDUs
  2. Khaki, coyote, or chocolate brown bottom weight cotton or similar fabric
  3. Two cargo-style pockets with a top flap along the outside of each leg, any closures are hidden
  4. Pants are worn tucked into the boots at the ankle

Optional Details:

  1. Rectangular padding approximately 15.3 cm x 10.2 cm (6 inches by 4 inches) added to the knees- proportional to the wearer
  2. Blue or red piping/trim on the edge of the pockets to match the piping on the jacket, if present.

Additional Images:

Shirt

Required Details:

  1. Tan, beige or middle brown shirt made of matte topweight natural fabric such as a broadcloth
  2. Collar ending in two points at the side front of the neck
  3. Front has a rectangular bib with seams on the bottom and both sides
  4. Long, plain sleeves without cuffs
  5. Closures are hidden
  6. Worn tucked into the pants
  7. Invisible closures (screen used closure was snap tape, other invisible closures also accepted)

Optional Details:

  1. Two rows of stitching around bib edges
  2. Vertical stitching on sides of bib continue to the bottom of the shirt
  3. Back yoke

Additional Images:

Belt

Option 1 Required Details:

  1. RFT style belt
  2. Dark tan to dark brown leather or leather-like belt
  3. Belt approximately 6 cm (2 inches) wide
  4. Octagonal silver buckle approximately 6-6.5 cm wide by 10.5 cm long (2-2.5 inches wide by 4 inches long)
  5. Worn on the pants or over jacket at the waist

 

Option 2 Required Details:

  1. Worn with the Fleet Captain/RFT Helmet
  2. Tan/Khaki/Coyote brown colored PLCE web belt with roll-pin buckle
  3. Worn over the top of the jacket at the waist
  4. Belt has a double layer of webbing with the outside layer creating a wave/loop effect
    (A British PLCE roll pin belt, which is worn inside out, is the most accurate belt.)

Optional Details:

  1. The belt contains 5 (five) vertical loops for mini-flares on both sides.

Boots

Required Details:

  1. Ankle high boot in brown or black leather or leather-like material
  2. No visible laces
  3. Anklet-style cuffs that match boot color, screen used were integrated as part of the boot

Optional Details:

  1. 2 silver signal flares held in the ankle cuff
  2. Spat-like detail stitching
  3. Vertical inside zipper
  4. Silver slider buckle attached to the cuff at the ankle back. Buckle is approximately 5 cm (2 inches) tall and sticks out to the back.

Additional Images:

Rank Badge

Required Details:

  1. Silver metal 5 cm (2″) square or with a metallic appearance
  2. Red or blue circles (pips) arranged in a pattern consistent with the rank of captain or higher
  3. Pips sit in indentations and are just below or flush with the badge face
  4. Worn on the right side of the jacket, just above the breast pocket.

OPTIONAL ITEMS

Helmet

Required Details:

  1. Oversized white domed (RFT style) helmet made of a hard material such as ABS plastic.
  2. Chin strap with a chin cup
  3. Tail-like extension piece on the back attached at the top of the head; extension continues the line of helmet ending approximately 10 -15.5 cm (4-6 inches) below the bottom of the helmet base.
  4. Dark visor
  5. Rectangular comm box

Optional:

  1. Antennae coming out of comm box

COSTUME RESOURCES:

Standard Authors: PArmstr, tenebris, RebelLady

Updated: Aug. 29, 2023

For Face Characters: Tattoos and body piercings – No tattoos or body piercings may be visible unless it is a tattoo/piercing the character has. They must be covered with makeup or by the costume.

PLEASE NOTE: The costume standards are a guide, yet are not an all inclusive outline of required elements. The judges will be looking for quality of workmanship, accurate execution and use of materials in addition to these general standards check lists. If you have a question about fabrics, colors, and parts choices for your build please contact the LCJs for your category about parts/materials you are considering before you start your build.